KINTEC RACING
Precision Perfomance Products
Zonda Cat

   


International buyers outside the USA will get a shipping invoice after checkout.


41" Carbon Fiber Catamaran  New V3 with thicker carbon fiber.
3/16 dual drive cnc machined aluminum stingers adjustable to 15 degrees.
3/16 flex cables and 3/16 drive shafts
Carbon fiber internal mounting plate for esc's, servo and receiver.
Right and left props.
3/16 2pc stainless collets.
Aluminum motor mounts. 
Aluminum stuffing tube installed with teflon liner.
Stainless drive dogs and stainless bullet nuts.
Dual pickup machined rudder with shear bolt.


Hull and Hardware no electronics  Includes every thing listed above except motors. Just install your own electronics. Everything mounted and ready to go.   $630.00

Hull and Hardware including Motors includes every thing listed above including Dual High Torque XL 3674 2075kv 4 pole motors. Aluminum water jacket. $680.00


ARTR

ARTR without Radio includes every thing listed above plus two Seaking 120amp esc's, Traxxas 2056 waterproof servo. $795.00


RTR w/ Flysky Radio includes every thing listed above plus two Seaking 120amp esc's, Traxxas 2056 waterproof servo, and Flysky FS-GT3C 2.4g radio and receiver. Recommended 4s or 5s lipos. $850.00



RTR w/ Futaba Radio includes every thing listed above plus two Seaking 120amp esc's, Traxxas 2056 waterproof servo, and Futaba 3PRKA 2.4g radio and receiver. Recommended 4s or 5s lipos. $870.00




FiberGlass w/ Carbon Kevlar Interior   Fiberglass version with carbon fiber and Kevlar reinforced interior. Comes with 2075kv SSS motors. Needs two ESC's and a servo.





Labor


PARTS




Dual Cooling Upgrade Rudder  Fits Popeye, Zonda, Genisis.  125mm total length. $17.00



Carbon Fiber Rudder  Made from solid carbon fiber sheet. Extra length rudder at 140mm (5 1/2") over all length. Fits the Popeye, Zonda, Genisis and our center mount cat  bracket.  $15.00


Zonda V1 One Pc Flex Cable  The V1 motor mount is approximately 11 3/8 inches from the transom.
 .187 (3/16)  flex cable with 3/16 ground shaft. Cut to length with soldered collet end and drive dog slot. Excellent quality and very strong. Very well balanced and true running. Best on the market. Has a 10-32 thread. Prop nut included. Made in USA. $25.00



Zonda V1 One Pc Reverse Wind Flex Cable The V1 motor mount is approximately 11 3/8 inches from the transom.
For right hand rotation prop.  .187 (3/16)  flex cable with 3/16 ground shaft. Cut to length with soldered collet end and drive dog slot. Excellent quality and very strong. Very well balanced and true running. Best on the market. Has a 10-32 thread. Prop nut included. Made in USA. $25.00



Zonda V2 One Pc Flex Cable   The V2 motor mount is approximately 8 1/2 inches from the transom.
.187 (3/16)  flex cable with 3/16 ground shaft. Cut to length with soldered collet end and drive dog slot. Excellent quality and very strong. Very well balanced and true running. Best on the market. Has a 10-32 thread. Prop nut included. Made in USA. $25.00


Zonda V2 One Pc Reverse Wind Flex Cable  The V2 motor mount is approximately 8 1/2 inches from the transom.
For right hand rotation prop.  .187 (3/16)  flex cable with 3/16 ground shaft. Cut to length with soldered collet end and drive dog slot. Excellent quality and very strong. Very well balanced and true running. Best on the market. Has a 10-32 thread. Prop nut included. Made in USA. $25.00


KR Dual Cooling Rudder Bracket  This is a direct bolt on replacement for the stock rudder bracket.


5mm x 3/16  Stainless steel 2pc collet that fits a 5mm motor shaft and 3/16 flex cable.  $10.00 each



5mm x 3/16 Reverse  Stainless steel 2pc collet that fits a 5mm motor shaft and 3/16 flex cable. Has a reverse thread for reverse wind flex cables.  $10.00 each



3/16 Flex w/ Square Drive  This is the stock replacement shaft that comes on the Zonda.
3/16 flex 11 7/8 (300mm) long with 3.7mm square drive on one end and round on the other. $8.00



3/16 Flex Reverse Wind w/ Square Drive   Stock 3/16 flex with reverse wind for counter rotating prop.
11 7/8 (300mm) long with 3.7mm square drive on one end and round on the other.  $8.00



3/16 Drive Shaft (Zonda)  This is the stock replacement shaft that came on the boat. Small diameter is 3/16 inch, large diameter is 1/4 inch, 100mm long, 2.7mm (.100) square drive.  $7.00


3/16 Stainless  Fits 3/16 shaft and has an outside diameter of .390 (10mm).    $3.00 ea


3/16 Prop Nut  For straight 3/16 shaft.  $3.00



36mm or 40mm Motor Mount  Machined aluminum mount with 25mm bolt pattern for 36mm or 40mm motors. Machined on 15 degree angle. $8.00


4 Inch Short Base Cat Rudder Hard anodized aluminum rudder with water pickup and shear bolt break away type. Has a pull-pull type linkage arm. Short base that sets the rudder 1.1 inch (28mm) from the transom.
Transom foot print is 1.1 wide and 7/8 inch high (28mm x 22mm)    $30.00



3/16 Adjustable Cat Stinger / Braced  Machined aluminum with stabilizer bracket. Adjusts 15 degrees. 3/16 teflon bearings installed. Total length is 4.3 inches (109mm).


Stainless Steel Strut Pin  Upgrade strut pin for the 3/16 cat strut used on the Zonda. Made from stainless steel for maximum strength. Only available at Kintec Racing.


Teflon Washers 3/16   Place between the drive dog and strut to prevent wear. Can be used on 3/16 or 4mm shafts. Pack of 5 for $3.00


Teflon Cable Liner    Replacement liner 12inch long (300mm).    $3.00
 


Brass Tube  Replacement stuffing tube with liner for Zonda.   300mm long (12").  $6.00


Replacement Motor  36x74 2075KV 4 pole High torque motor w/ cooling jacket.


SSS 3674 2075kv



X442  Has a diameter of 42mm and pitch of 1.4  Fits 3/16 shaft  $22.00



X442/3 Has a diameter of 42mm and a pitch of 1.4  Fits a 3/16 shaft. $22.00



M842/3  Has a diameter of 42mm and pitch of 1.8  Fits 3/16 shaft.  $24.



X443  Has a diameter of 43mm and pitch of 1.4  Fits 3/16 shaft.  $22.00



X445  Has a diameter of 45mm and pitch of 1.4  Fits 3/16 shaft.  $26.00



X442-R  Reverse rotation. Has a diameter of 42mm and pitch of 1.4  Fits 3/16 shaft.  $22.00



X442/3-R Has a diameter of 42mm and a pitch of 1.4  Fits a 3/16 shaft. $22.00



M842/3-R  Reverse rotation. Has a diameter of 42mm and pitch of 1.8  Fits a 3/16 shaft. $24.



X443-R  Reverse Rotation. Has a diameter of 43mm and pitch of 1.4  Fits 3/16 shaft. $22.00


X445-R  Reverse rotation.  Has a diameter of 45mm and pitch of 1.4  Fits 3/16 shaft.  $26.00


Exhaust Pipes  Machined aluminum dummy exhaust pipes. Can be bolted on with 3mm bolts or epoxied to hull. Comes in a pack of 4pcs for $4.00



Carbon Fiber Replacement Hatch


Back to Top of Page

Website Builder