Motor Mounting Hex Key Set This is a must have for installing motors in most FE boats. Made with 1/4 hex stock and 2.5mm High Torque Allen key. Use with your socket or open end wrench to make motor installation so much easier. $7.50
Stainless Tweezers Set
Stainless steel and non magnetic. Great for holding small wires for soldering and retrieving nuts and bolts in your boat. 5 inches long. One straight and one 45 degree. $4.75 per set.
GP Dead Center Hole Locator
For Locating Mounting Holes. The tool is extremely easy to use. Simply press its self-centering alignment cone into the mounting hole and give the handle a few turns, the sharp drill tip leaves perfectly centered marks every time!
Mr Grippy Soldering Jig
Carbon Fibre construction and supplied with rubber 'feet' to prevent sliding on your workbench. Spring loaded sliding action. Great for holding wires, Deans, Xt60, and up to 5.5 bullets.
2.75" x 2.36" x 1.18" (70mm x 60mm x 30mm) $13.00
Soldering Jig Anodized aluminum soldering jig with non skid feet on the bottom. Holds most connectors such as Deans, Traxxas, XT60, Micro Deans, EC3, EC5. A variety of bullets such as 3.5mm, 4mm, 5.5mm. $20.00
Hobbico Soldering Iron 60 Watt Comes with 2 flat chisel tips and a table stand. Very affordable.
Novak Lead Free Silver Solder
Specially formulated for hand soldering. Contains 3% silver for
high-conductivity, low-resistance and strong solder joints at a
relatively low melting point. 100g $38.00
Trak Power Lead Free Silver Solder
Rosin Core Solder.
Specially formulated for hand soldering. Contains 3% silver for high-conductivity, low-resistance and strong solder joints at a relatively low melting point. 15g $8.60
TrakPower TK60 60watt Soldering Iron
110volt, Power on indicator lamp, Slender non-slip grip, Heavy duty 3-prong power cord, Replaceable 2.4mm chisel tip, One year limited warranty through TrakPower beginning at date of purchase.
TrakPower Chisel Tip 2.4mm
This is the 2.4mm Chisel Tip for the TrakPower TK 60 Soldering Iron. $2.70
TrakPower Cleaning Wire w/ Holder m
Works with all brands and shapes of soldering iron tips. Wire sponge cleans solder tips without messy water based sponges. Enclosed two-piece aluminum housing opens for easy access to sponge. Rubber feet on bottom eliminates sliding on workbench. $9.00
TrakPower TK-950 Soldering Station
Heavy-duty 60 watt design. Heats quickly to selected temperature within a range of 392°-896°F. Holds setting within 1.8°F when idle. 5-year warranty on unit, 1 year warranty on iron handle's electronics. Includes
Soldering iron with stand, sponge, temperature control unit, chisel point tip, pencil tip, instruction manual and decals. One of the best on the market and worth every penny. $80.00
TrakPower Sponge TK950 m
This is the Sponge for the TrakPower TK950 Soldering Station. $2.30
TrakPower Chisel Tip 2.4mm TK950
This is the 2.4mm Chisel Tip for use with the Team Checkpoint TK-950 Soldering Station. $5.50
TrakPower TK955 Digital Soldering Station
Digital LED display shows selected temperature, heating status and
Push button controls adjust heat in precise 1° increments
Security key locks in selected temperature, preventing accidental
Holds selected temperature within 1.8°F (1°C) while idle.
Five year limited warranty on the base unit, and one year limited
warranty on the iron handle from date of purchase. This warranty
does not cover damage caused by abuse, misuse, alteration or
accident. Power: 60W
Temperature: 392-896° F (200-480° C)
Yihua 936 Soldering Station m 45W Output 110VAC input. Adjustable Temperature range from 392-896F 200-480C. A nice unit for the money. $25.00
Yihua Soldering Tips Set of 10 soldering iron tips for the Yihua station
Metric Nut Driver Set These are short length nut drivers perfect for working inside the boat where space is limited. Makes tightening the transom nuts so much easier. A must have for boaters. Sizes are laser etched on a knurled aluminum handle. Includes 4mm, 4.5mm, 5.5mm and 7mm. $8.75
Long Neck Needle Nose Pliers with wire cutter. Perfect size for reaching anywhere. Nice compact size yet long enough to make the job easy. 6 inch total length. Drop forged.
Cutting edge is induction hardened.
X-ACTO Type Razor Knife Knurled aluminum handle with collet for interchangeable blades. Comes with 1 SK-5 blade and protective cap. Only $1.50
SK-5 Razor Replacement Blades 10pcs for $2.00
Snap Off Razor Knives
Large is 3/4"wide with 8 blades. Small is 3/8"wide with 10 blades. Large only .25 cents each. Small is only .15 cents each.
Bondhus Balldriver 8pc Standard allen wrench set From the inventors of the ball driver and still Made in USA. Ball drivers allow you to put wrench on an angle in tight locations. These are still the best and allow for the greatest angle.
Includes .050, 1/16, 5/64, 3/32, 7/64, 1/8, 9/64 and 5/32" wrenches. Bondhus lifetime warranty. $7.70
Bondhus Balldriver 6pc Metric allen wrench set From the
inventors of the ball driver and still Made in USA. Ball drivers allow
you to put wrench on an angle in tight locations. These are still the
best and allow for the greatest angle.
Includes 1.5, 2.0, 2.5, 3.0, 4.0 and 5.0mm wrenches. Bondus lifetime warranty. $6.30
Bondus .050 Ball Driver For use with KR small Dog and Octura small dogs. $1.25
Bondus .050 High Torque Key High Torque allen keys are slightly over size for a snug fit to help prevent stripping. For use with KR small Dog and Octura small dogs. $.75
Bondus 1.5mm High Torque Key High Torque allen keys are slightly over size for a snug fit to help prevent stripping. $.75
Bondus 2mm High Torque Key High Torque allen keys are slightly over size for a snug fit to help prevent stripping. $.75
Bondhus Balldriver 8pc Standard Hex Set
Balldriver screwdrivers feature ergonomically designed handles that are comfortable to use. Only available from Bondhus, Protanium steel blades means these are the strongest ballpoints available. The 8 blade sizes in this set are: .050, 1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32. Lifetime warranty. $22.00
Bondhus Balldriver 6pc Metric Hex Set
Balldriver screwdrivers feature ergonomically designed handles that are
comfortable to use. Only available from Bondhus, Protanium steel blades
means these are the strongest ballpoints available. Includes 1.5, 2, 2.5, 3, 4 and 5mm sizes. Lifetime warranty. $18.00
Dubro Tubing benders
Designed for use with brass or aluminum tubing. Does not collapse tubing. Perfect for making water or feul lines. The 1/8 bender works on tubing from 1/8-1/16. The 5/32 bender works on tubing from 5/32 to 9/64. Tubing sizes measured on the outside diameter.
K&S Tubing Bender Kit
For 1/16 to 3/16 OD Brass, Aluminum, Copper tubing. Prevents kinks when bending. 5 different sizes included. $3.10 per kit
K&S Tubing Cutter For Brass, Aluminum, Copper tubing up to 5/8inch diameter.
Makes a clean straight cut without kinking. $6.20 each
Excel Assorted Files w/ Handle 6 assorted files 5 1/2 long, 1/8 shank. Set includes flat, knife, half-round, square, round, triangular, and pointed flat.
Excellent set for sharpening props. $11.25
Wiha Proturn Precision Screwdriver Set m
With Technicians System 4 Collet Lock handles.
slotted on one end, phillips on the other. Special performance CVM tool steel blades.
Hardened for maximum durability. Black oxide finished blades and tips. Exact fit precision machined tips.
Molded ergonomic, anti-static handle. Free turning finger tip control cap.
Handle allows adjustable blade length (15mm-95mm / .6"-3.75").
Narrow profile handle for maneuverability in tight locations. Blades also fit standard handles. Guaranteed quality.
Tip Sizes (Phillips x Slotted):
#000 x 1.5mm, #00 x 2.0mm, #0 x 3.0mm, #1 x 4.0mm Made in Germany $23.00
Bondhus Felo Screwdriver Set 6 pc screwdriver set has both slotted and phillips styles. Hardened tips and chrome shafts.
Rotating caps increase fingertip control. Comes in a hard case. Top shelf set. $26.70
Clevis Driver Makes installing clevises easy. Prevents twisting or damage to the clevis. $1.00
Aluminum Magnetic Parts Tray Aluminum parts tray with magnetic pad and skip proof feet.
115mm x 85mm x 15mm.
DuBro E/Z Bender Wire forming tool.
Works on .062" - .093" (1.6mm -2.4mm) diameter wire. Will bend wire from 0-90 degrees. Makes perfect Z-bends, L-bends in linkage. $22.50
Demo video of E/Z Bender by DuBro