Traxxas #2056 Waterproof High Torque Servo
with J style connector. $28.00
The first fully waterproof servo on the market. 80 oz/in of torque
Length 2.16" (55mm)
Height 1.69" (43mm)
Weight 1.58oz (45g)
0.23 sec @ 60°
Traxxas 2053 Gear Set Replacement gear set for 2056 and 2055 servo.
Traxxas #2075 Digital High Torque Servo
J style connector. $40.00
SPECS: Length: 55mm (2.17")
Width: 20mm (0.79")
Height: 42.3mm (1.67")
Torque: 125 oz-in
Speed: 0.16 sec @ 60°
Traxxas 2072 Gear Set Replacement gears set for 2070 and 2075 servos. $3.70
Traxxas #2080 VXL Micro Water Proof Servo Waterproof with standard plug. $25.00
SPECS: Length: 29.5mm (1.2")
Width: 14mm (0.55")
Height: 29mm (1.1")
Torque: 41.7 oz-in
Speed: 0.11 sec @ 60°
Ace 8170 Digital High Volt Waterproof Servo
Compatible with 2S LiPo or LiFe batteries without needing to use a
Three titanium and one alloy aluminum gear for continuous non-stop
operation and reduced weight.
High torque output with low current draw.
Water and dust resistant.
Aluminum middle case section for efficient heat dissipation.
High performance coreless motor.
INCLUDES: 8170 Digital High Voltage Heli Servo with Lead and Connector, 1.9"
(47.5mm) double sided Servo Horn
Four each, Grommets, Eyelets, 3x11mm Screws and 3mm Locknuts
SPECS: Voltage Range: 6.6-7.4V (2S LiPo or LiFe)
Pulse Width: 1520us
Torque: 14.5 kg-cm @ 7.4V
Transit Time: 0.06 sec/60° @ 7.4V
Dimensions: 1.6 x 0.81 x 1.5" (41.8 x 20.6 x 39.6mm)
Weight: 2.19oz (62g). $99.99
Futaba S3003 Standard Servo
This basic servo is used in cars, boats, or where standard servos are used.
INCLUDES: One S3003 standard servo with preinstalled Xshape servo horn FUTM0031
Four brass eyelets
Four Black rectangular rubber grommets
Four servo mount screws
One servo wheel 1-3/8" (35mm) in diameter
One X-shape servo arm 1.5" (38mm) across
One star shaped arm 1-1/4" (32mm) across $11.00
Futaba S3305 High Torque Standard Servo w/ Metal Gears
Wide usage in cars and boats that require standard size, high torque servos. Two ball bearings, 3-pole motor, Standard Futaba J style connector.
INCLUDES: One Futaba S3305 High Torque Metal Gear Servo with 1.5" (39mm) diameter horn.
1.2" (32mm) 6 point horn
4 eyelets, 4 rubber
grommets, 4 mounting screws. $35.00
Speed: 0.25 sec/60° @ 4.8V, 0.20 sec/60° @ 6V
Torque: 124 oz-in (8.9 kg-cm) at 6V, 99 oz-in (7.1 kg-cm) at 4.8V
Futaba S3306MG 1/5 High Torque High Speed
For 1/5 scale RC vehicles, Dual ball bearings, Metal gears.
INCLUDES: S3306MG Servo with (30mm) Round Horn, 3.8" (97.3mm) 4-Point Horn, 3.4" (87.5mm) 6-Point Horn and Mounting Hardware.
Speed: 0.16 sec/60° at 6.0V
Torque: 333 oz/in (24.0 kg/cm) at 6.0V
Size: 2.60 x 1.18 x 2.25" (66 x 30 x 57.1mm) $50.00
Futaba S9157 Digital High Torque
Coreless motor, Dual ball bearings and metal gears, Metal middle case helps dissipate heat for cooler operation.
INCLUDES: Futaba S9157 High Torque Servo with 0.83" (21mm) diameter round horn,
1.8" (45mm) diameter round horn, 1.2" (31.5mm) 6 point horn, 1.5"
(38.5mm) 4 point horn and mounting hardware
SPECS: Torque: 425oz-in (30.6kg/cm) @ 6V
Speed: 0.14 @ 6V
Size: 1.6 x 0.8 x 1.5" (41 x 21 x 37mm)
Weight 2.5oz (71g)
Horn Screw Size: 3x8mm
Hitec Micro HS-5086WP Digital Waterproof Metal Gear
With high voltage capability, heavy-duty metal gears and a ball bearing
supported output shaft. Dimensions: 1.22 x 0.60 x 1.22 in. Weight: 1.0 oz.
Speed (6V) : 0.18, Torque (6V): 42 oz-in
Speed 7.4V): 0.15, Torque (7.4V): 50 oz-in $50.00
Hitec HS-5646WP Digital Waterproof High Torque High Volt MG Dual BB
Industry first true water proof digital servo (IP67 Industrial
Ideal for boats, 1/8 and 1/10 scale cars. 7.4V 2-cell LiPo and 6-cell NiMH compatible. Ball bearing equipped metal gears. Programmable digital amplifier with MOSFET drive.
INCLUDES: HS-5646WP Servo, 1.8" (45mm) Round Horn, 2.3" (57.5mm) Double Arm
Horn, 1.6" (42mm) Four-Point Horn, 1" (26mm) Single Arm Horn and
SPECS: Size: 1.65 x 0.83 x 1.57" (41.8 x 21 x 40mm) Weight: 2.15oz (61g)
Torque: 7.4v=179.14oz.in (12.9kg.cm)
6.0v=156.92oz.in (11.3kg.cm) $55.00
Hitec HS-5485HB Digital
Programmable Standard Digital Servo with Hitec "S" Type Connector. Four heavy duty Karbonite gears. Top ball bearing. $22.00
Specs: Speed: 0.20sec/60 degrees at 4.8V INCLUDES: One servo with pre-installed round (disk) servo horn
Torque: 5.2 kg-cm (72 oz-in) at 4.8V Four grommets
Length: 39.8mm (1.57") Four brass eyelets
Width: 19.8mm (0.78") Four flanged, phillips head screws 1.5 x 14mm
Height: 38.0mm (1.49") One adjustable servo horn
Weight: 45g (1.59oz) One large X servo horn 1.7" (43mm)
One small X servo horn 1.2" (30mm)
One straight servo horn 1.3" (33mm)
Hitec HS-77BB Low Profile Comes with a
Universal Futaba J, Hitec S, JR and Airtronics Z Connector.
One ball bearing on the output shaft. One internal metal gear. Nylon output gear. Water tight.
Specs: Dimensions: 44x23x25mm (1.7x0.9x1.0")
Weight: 35 grams (1.23oz)
Speed: .18sec/60° @4.8V .14sec/60° @6.0V
Torque: 61.1 oz-in @4.8V, 76.3 oz-in @6.0V
Hitec HS-645MG High Torque Metal Gear Servo
Ultra Torque, Metal Gear Servo with a Futaba J, Hitec, JR, and Airtronics-Z Style Connector. Three metal gears. Dual ball bearings. Four adjustable splined horns.
Specs: Speed: 0.24 sec/60° at 4.8V Includes: One white small X-shaped servo horn
0.20 sec/60° at 6.0V One red Large X-shaped servo horn
Torque: 106.93 oz-in at 4.8V (7.7 kg-cm) One white adjustable servo horn
133.31 oz-in at 6.0V (9.6 kg-cm) One white offset straight servo horn
Length: 1.59" (40.6mm) Four 2 x 14mm mounting screws
Width: 0.77" (19.8mm) Four brass eyelets
Height: 1.48" (37.8mm) Four black rubber vibration isolators
Weight: 2.11oz (60g)
Futaba Brand 3 inch Servo Extension
Gives you 3 more inchs of length from servo or esc to reciever. Has standard J connector.
Futaba Brand 8 inch Heavy Duty Extension Gives 8 inches more length from servo or esc to receiver. Has standard J connectors one male and one femal. Made with heavy 20 gauge wire for higher current loads.
Futaba 4 inch Extension 10cm extension with one male and one female connector. $1.00
Servo Extension 16" inch long (42cm) servo extension with one female and one male connector.
Fits JR or Futaba.
Futaba Heavy Servo Extension 6"
Made from 22awg wire $1.50
Futaba Heavy Servo Extension 12" Made from 22awg wire. $2.00
Futaba / JR Extension Locks Keeps servo extension wires from coming apart. Made for Futaba but also fits JR.
1pc for .50 or 5pcs for $2.00
Hitec Heavy Duty Y Harness 6 inch length with
Hitec S, JR, Airtronics Z Connectors. Heavier, 20-gauge wire handles higher current loads. Great for connecting 2 esc's to one radio. $10.30
JR/Hitec Long Y Harness 12 overall length with JR, Hetec Connectors. $6.00
Futaba Y Harness 6" 1 male and 2 female connectors. $2.00
JR Y Harness 6" 1 male and 2 female connectors. $2.00
JR Extension Locks Keeps servo extension wires from coming apart. Made for JR but also works with Futaba.
1pc for .50 or 5 pcs for $2.00
JR 4 inch Extension
4inch (10cm) long extension with one male and one female connector. $1.00
JR Heavy Servo Extension 6" Made from heavy 22awg wire. $1.50
JR Heavy Servo Extension 12" Made from heavy 22awg wire. $2.00
KR Delrin Servo Mount Made for standard size servos. Drilled for 3mm machine screws. Can be epoxied to hull. Slotted base for adjustment if you wanted to use t-nuts to secure to the hull. Sold in pairs. Another quality Kintec Racing product made in USA. $7.50