KINTEC RACING
Precision Perfomance Products
Popeye Hydro
 

 


ARTR Popeye Hydro  Fiberglass hydro that is 33 inches long and 14 inches wide (822mmx160mm). Comes with a 4 pole 36x74 motor 2075kv, Seaking 120 Amp esc. Drive system is a 2 pc 3/16 flex and drive shaft. Cnc machined hardware. Excellent running hydro. Great for the P class 4s lipo setup. No need for upgrades does 45mph out of the box. Giant inside with a lot of room to spare for the people that need to push this over the limit. All you need is a servo and radio to get you going.


Fiberglass Bare Hull  White gelcoat.


  Carbon Fiber Popeye Hydro   33 inches long and 14 inches wide (822mmx160mm). Comes with a Leopard 40x74 motor 2200kv. Drive system is a 2 pc 3/16 flex and drive shaft. Cnc machined hardware. Excellent running hydro. Great for the P class 4s lipo setup. Giant inside with a lot of room to spare for the people that need to push this over the limit. All you need is a servo, esc, and radio.




Dual Cooling Upgrade Rudder  Fits Popeye, Zonda, Genisis.  $17.00



Carbon Fiber Rudder  Made from solid carbon fiber sheet. Extra length rudder at 140mm (5 1/2") over all length. Fits the Popeye, Zonda, Genisis and our center mount cat  bracket.  $15.00


3/16 One Piece Popeye Upgrade Shaft  Replaces the stock 2 pc shaft for easier greasing and lasts longer. Includes 10-32 lock nut, drive dog slot, and soldered collet end.


Hydro Turn Fin
  
CNC machined aluminum. 67mm long and 42mm wide.  $12.



Upgrade Turn Fin Bracket  Made for the Upgrade Hydro Turn Fin. discontinued. $7.00



Heavy Duty Hydro Turn Fin Bracket  Machined aluminum to the correct angle for the Popeye Hydro. No mods needed, drilled for the stock holes.  $12.50


Popeye Turn Fin Nut Plate  Aluminum nut plate for the popeye turn fin. Made for the stock holes to replace washers and nuts. Helps prevent cracking of the sponson and makes installing the fin much easier. $5.00


Replacement Motor  36x74 2075KV 4 pole High torque motor w/ cooling jacket. $49.00


3/16 Flex w/ Square Drive  This is the stock replacement shaft that comes on the Popeye.
3/16 flex 11 7/8 (300mm) long with 3.7mm square drive on one end and round on the other. $8.00



5mm x 3/16  Stainless steel 2pc collet that fits a 5mm motor shaft and 3/16 flex cable.  $10.00 each



3/16 Stainless  Fits 3/16 shaft and has an outside diameter of .390 (10mm).    $3.00 ea


Brass Tube  Replacement stuffing tube with liner for Zonda.   300mm long (12").  $6.00


KR Dual Cooling Rudder Bracket  This is a direct bolt on replacement for the stock rudder bracket.


4 Inch Short Base Cat Rudder Hard anodized aluminum rudder with water pickup and shear bolt break away type. Has a pull-pull type linkage arm. Short base that sets the rudder 1.1 inch (28mm) from the transom.
Transom foot print is 1.1 wide and 7/8 inch high (28mm x 22mm)    $30.00



3/16 Rigger/Hydro Strut  Aluminum adjustable strut for 3/16 shaft with teflon bushings installed. Small transom foot print which is great for riggers, hydros or any boat with a small transom.  $16.00
38mm (1.5") from top of bracket to bottom of strut, adjustable height.
transom foot print is 15mm (.59") high and 27.1mm (1.07") wide.
strut length is 40mm (1.58") long.


Small Hydro/Rigger Turn Fin  CNC machined clear anodized aluminum. Comes with mounting bracket and hardware.  46mm long x 31 mm wide x 2mm thick.  (1.8 x 1.2 x .078 inches)  $6.00


Fiberglass Replacement Hatch
Website Builder