KINTEC RACING
Precision Perfomance Products
Motor Mounts


36mm or 40mm Motor Mount  Machined aluminum mount with 25mm bolt pattern for 36mm or 40mm motors. Machined on 15 degree angle. $8.00


56mm Motor Mount  Machined aluminum. For 56mm motors. 30mm bolt pattern. 100mm  long x 66mm wide x 65mm high. Mounts motor on an 8 degree angle. $18.00



56mm Carbon Fiber Motor Mount  For 5682-5692 motors. Adjustable length. Carbon fiber side rails with anodized aluminum mounting brackets. Adjustable height that can be used on both vee bottom or cats. Shown with a 5692.  $52.00


5 Inch Rail Adapter This set will adapt the 56mm carbon fiber motor mount shown above to a 5 inch rail set up. All nuts and bolts needed included. Motor mount sold separately. $17.50


5692 Aluminum Motor Mount 



5 Inch Rail Adapter Set  This set will adapt the 56mm aluminum motor mount show above to a 5 inch rail setup. All nuts and bolts needed included. Motor mount sold separately. $25


Carbon Fiber Motor Mount Stringer Assembly Made to keep everything in line and on center for better center of gravity. Can be used with 36mm or 40mm diameter motor mounts 74mm-92mm long. Use Aluminum stuffing tube T-bar for stuffing tube adjustment both up and down and correct angle alignment. Moves the servo to center for more lipo adjustment. Motor mounts, servo and t-bar sold separately. Another quality Kintec Racing product. $23.00
 


KR 2 Axis Aluminum Motor Mount   Made for flat bottom or deep vee installs. This motor mount allows for angular adjustment and height alignment.  Allows you to remove the motor without removing your collet. Fits 36mm and 40mm diameter motors. Only available at Kintec Racing. Sweet at only $25.00


KR 2 Axis Motor Mount Plate  Made for flat bottom or deep vee installs. Increased adjustability and is a direct bolt on replacement for the TFL mounts, no mods required.  $7.00


KR 2 Axis Carbon Fiber Motor Mount   Made for flat bottom or deep vee installs. This motor mount allows for angular adjustment and height alignment.  Allows you to remove the motor without removing your collet. Fits 36mm and 40mm diameter motors. Only available at Kintec Racing. Sweet at only $22.00


KR X-Long 2 Axis Aluminum Motor Mount   Fits 36mm or 40mm diameter motors. Made for flat bottom or deep vee installs. This motor mount allows for angular adjustment and height alignment to the stuffing tube. Multiple mounting holes for the lowest possible center of gravity. Nice large opening for thrust bearings and allows you to remove the motor without removing the collet. The adjustable tail brace allows for any length motor and up to a 70mm water jacket. The low profile makes installing and motor maintenance easier. Tail ring sold separately. Only available at Kintec Racing.  $30.00



KR X-Long 2 Axis Carbon Fiber Motor Mount   Fits 36mm or 40mm diameter motors. Made for flat bottom or deep vee installs. This motor mount allows for angular adjustment and height alignment to the stuffing tube. Multiple mounting holes for the lowest possible center of gravity. Nice large opening for thrust bearings and allows you to remove the motor without removing the collet. The adjustable tail brace allows for any length motor and up to a 70mm water jacket. The low profile makes installing and motor maintenance easier. Tail ring sold separately. Only available at Kintec Racing.  $30.00


540 Motor Mount Face Plate only  Water cooled face plate fits 540 motors 36mm or 40mm in diameter. $8.00


540 Motor Mount Face Plate CNC machined aluminum water cooled face plate, fits 540 motors 36mm or 40mm in diameter. Can be used with either 36 or 40mm tail rings.  $8.00



36mm Tail Ring  Fits motors with a 36mm diameter.  $6.00



36mm Tail Ring  Fits motors with a 36mm diameter can. $6.00



40mm Tail Ring  Fits motors with a 40mm diameter can.  $6.00



40mm Tail Ring  Fits motors with a 40mm diameter can. $6.00



380 Water Cooled Motor Mount   Machined aluminum with fiberglass side plates. Fits 380 sized motors (28mm dia) that have hole spacing 16-19mm.  $13.00



Motor Mount 380-540



Water Cooled Motor Mount 380-540  Machined aluminum motor mount with G10 side plates. Fits 36mm-40mm diameter motors or (380-540) sized motors. All stainless hardware included.   $13.00
 


36mm 540XL Motor Mount  Water cooled aluminum motor mount for 36mm diameter motors. Fiberglass side plates. Rear support for L and XL motors. 3 5/8 inch (92mm) long.  $20.00 each


Carbon Fiber 540XL Motor Mount   Aluminum water cooled motor mount with carbon fiber side plates.  Has rear support for L and XL motors. Fits 540 (36mm) sized motors.  3 5/8 inch (92mm) long.    $23.00 ea
 


Carbon Fiber 540XL Motor Mount   Aluminum water cooled motor mount with carbon fiber side plates.  Has rear support for L and XL motors. Fits 540 (36mm) sized motors.  3 5/8 inch (92mm) long.    $25.00 ea
 

40mm Motor Mount   Aluminum water cooled motor mount. Fits motor with a 40mm diameter can. Total length is 100mm (3.93") Width is 58mm (2.28")  $20.00
 

40mm Motor Mount   Aluminum water cooled motor mount. Fits motor with a 40mm diameter can. Total length is 100mm (3.93") Width is 58mm (2.28")  $20.00
 


40mm Carbon Fiber Motor Mount    Aluminum water cooled motor mount with carbon fiber side plates.  Fits motors with a 40mm diameter can. Total length is 100mm (3.93") Width is 58mm (2.28")    $25.00


40mm Carbon Fiber Motor Mount   Aluminum water cooled motor mount with carbon fiber side plates.  Tail ring is 40mm diameter. Total length is 100mm (3.93").  Width is 58mm (2.28").    $25.00 ea


540 Motor Mount.   Anodized aluminum. Can be easily adjusted on an angle. Made for motors with 25mm bolt spacing.  $3.00



Water Cooled Cat Mount  Aluminum cat mount for 540 motors with fiberglass base. 25mm bolt pattern. Mount is 45mm wide and 45mm high. Base is 40mm wide. $10.00


Large Water Cooled Cat Mount  Aluminum cat mount for 540 motors with fiberglass base. 25mm bolt pattern with 3mm holes. Mount is 50mm wide and 52mm high. Base is 40mm wide. $10.00



Single Side Rigger Mount  Adjustable machined aluminum clamp style with fiberglass side frame. Fits motors with a 28mm diameter can. Great for riggers or where space is limited. $10.00



Single Side Rigger Mount  Adjustable machined aluminum clamp style with fiberglass side frame. Fits motors with a 29mm diameter can. Great for riggers or where space is limited. $10.00


5692 Motor Mount 



40mm Zip Kits Rigger Mount Assembly


VS1 Motor Mount Plate    Internal motor mount plate.   Standard bolt pattern that is threaded so no need for locknuts and washers.  $5.50
 


SV27 Water Cooled Motor Mount  This is a bolt on replacement unit machined from 6061. Threaded sides making installation much easier no need from lock nuts. Exact same spacing as the stock mount. Enlarged center hole so motor can be removed without removing collet. Water cooled to draw heat from motor face. Comes with nickle plated banjo fittings which can be pointed front, up or back.     width is 2.91 inches (74mm)
Another quality Kintec Racing product.   Made in USA
Website Builder