KINTEC RACING
Precision Perfomance Products
Building Supplies                


1/4 Adjustable Stuffing Tube Bracket
  Fully adjustable bracket for 1/4 brass tube. Adjustable height, any angle and if installed with spacer washers can be adjusted side ways also. Perfect for scratch building on monos or cats. Great upgrade for the UL-1 or Motley Crew.



9/32 Adjustable Stuffing Tube Bracket
  Fully adjustable bracket for 9/32 brass tube. Adjustable height, any angle and if installed with spacer washers can be adjusted side ways also. Perfect for scratch building on monos or cats.



7mm Adjustable Stuffing Tube Bracket
  Fully adjustable bracket for 7mm brass tube. Adjustable height, any angle and if installed with spacer washers can be adjusted side ways also. Perfect for scratch building on monos or cats. Great upgrade for the Pursuit.



1/4 Stuffing Tube T Bar  Machined aluminum t bar to brace a 1/4 stuffing tube. 53mm (2.087") long. $10.00


KR Delrin Angle Bracket  Machined for use with the T bar stuffing tube brackets. Allows for height and angle adjustment of stuffing tube. Can be epoxied to hull or lay fiberglass or carbon fiber over leg to secure. Sold in pairs. T-Bars sold separately. Another quality Kintec Racing product made in USA. $7.50



7mm Stuffing Tube T Bar  Machined aluminum t bar to brace a 7mm stuffing tube. 53mm (2.087") long. $10.00


9/32 Stuffing Tube T Bar  Machined aluminum t bar to brace a 9/32 stuffing tube. 53mm (2.087") long. $10.00


Servo Stringer Assembly  Carbon fiber servo stringer assembly. Use with aluminum stuffing tube T-bar shown above. Allows for stuffing tube adjustment up and down and for proper angle to motor. Servo and T bar sold separately. Another quality Kintec Racing product. $16.00


Carbon Fiber Motor Mount Stringer Assembly Made to keep everything in line and on center for better center of gravity. Can be used with 36mm or 40mm diameter motor mounts 74mm-92mm long. Use Aluminum stuffing tube T-bar for stuffing tube adjustment both up and down and correct angle alignment. Moves the servo to center for more lipo adjustment. Motor mounts, servo and t-bar sold separately. Another quality Kintec Racing product. $23.00
 


Extra Long Zip Ties  12" long. Perfect width for use with servo or esc mounts.  10pcs for $1.00



5" Stuffing Tube T bar  Machined aluminum t bar with oiler. Adjustable length from 4 7/"8 (127mm) to 5 1/4" (133mm)  $24.00


Expandable Marine Foam This expandable 2 part polyurethane water proof flotation boat foam is low density and closed cell. It weighs 2 pounds per cubic foot. Each kit contains 3oz of each part A and B.  $10.00 per kit.
Ships to US customers only.


Carbon Fiber Cloth  This is 2X2 twill weave 5.7oz weight which makes it perfect for draping over complex curves.

Sizes


Carbon Fiber / Kevlar Hybrid Cloth  This is 2x2 twill weave. Very flexible. Available in 12x16 or 16x24 inch squares. Colors are black/blue, black/red, black/yellow, black/blue/yellow, black/orange.

Sizes / Colors


Carbon Fiber Sheet   100mm wide x 300mm long  (3 15/16" x 11 13/16")  Available in thickness of 1mm, 1.5mm, 2mm, 2.5mm
 
Thickness


Fiberglass Battery Tray  Made from strong fiberglass material. Bottom side shown in photo. Can be used with or without tabs. With tabs allows for Velcro to be wrapped around lipos and under tray. 56x140mm (2.2x5.5") $6.00 each


Carbon Fiber Battery Tray  Made from 2mm carbon fiber. Can be used with or without tabs. With tabs allows for Velcro to be wrapped around lipos and under tray. 56x140mm (2.2x5.5") $8.00 each


Carbon Fiber Long Battery Tray  Can be used with or without tabs. With tabs allows for Velcro to be wrapped around lipos and under tray. 56x200mm (2.2x7.9") $14.00


Carbon Fiber Long Notched Battery Tray 200x56mm (2.2"x7.9")  16.00 each


Carbon Fiber XL Battery Tray  Can be used with or without tabs. Allows for larger lipos and maximum cg adjustment. 56x300mm (2.2x11.8") $19.00 



Carbon Fiber XL Notched Battery Tray  Can be used with or without tabs. Allows for larger lipos and maximum cg adjustment. 56x300mm (2.2x11.8") $20.00



Carbon Fiber 2XL Battery Tray  Can be used with or without tabs. Allows for larger lipos and maximum cg adjustment. 56x350mm (2.2x11.8") $19.00



Carbon Fiber ESC Mount  Perfect for mounting your Seaking esc. made from 2mm carbon fiber sheet. $5.00



Carbon Fiber SwordFish ESC Mount  Perfect for mounting Larger esc's. 4.5" x 3.14" (120mm x 80mm)
Made from 2mm carbon fiber sheet. $10.00



Carbon Fiber Rod   Great for stiffening hulls or fillets on motor mounts and servo mounts.  Slide over steering linkage to eliminate any flex.  Sold in 12 inch length.
.125= .125" OD x .060" ID (3.2mm OD x 1.5mm ID)
.157= .157" OD x .098" ID (4mm OD x 2.5mm ID)----Use over 2-56 or 2mm rods
.188= .188" OD x .116" ID (4.8mm OD x 3mm ID)----Use over 4-40 rod
.196= .196" OD x .121" ID (5mm OD x 3.1mm ID)----Use over 3mm rod
.210= .210" OD x .132" ID (5.3mm OD x 3.4mm ID)

Sizes


Fiberglass Strips  2" wide x 5 feet long. Medium weight. Great for adding strength to seams or surfaces.
 


Fiberglass Strips 3" wide x 5 feet long. Heavy weight. Great for adding strength to seams or surfaces. $4.50



Fiberglass Cloth  1 square yard of 2 oz.  Highest quality and toughest weave available. Excellent contouring qualities make it easy to apply to compound curves. Made especially for use with polyester or epoxy resin.


Z-Poxy PT-40  Finishing Resin. This is must have stuff for any boater. Waterproofs wood, strengthens hulls great for laying fiberglass or carbon fiber cloth. Odorless and sands easily.  12 FL oz.   $13.00ea  This box is heavy and shipping is approximately $6.75 for 10 items with this item. Should paypal shipper charge twice a refund will be sent.



Disposable Epoxy Brushes       1/2 inch wide pure horsehair acid brushes 6 inches long. Wider then most stores carry. They have a hollow handle which is nice when you need to get up into the bow nose, just cram a stick or pencil in for an extra long reach.   10 horsehair brushes for $2.75
Also stocking 3/8 wide nylon brushes.  6 nylon brushes for $1.40
   
Type


Epoxy Mixing Cups  1oz graduated mixing cups. Nice raised letters that are very easy to read. Makes accurate mixing of any 2 part epoxy so much easier, no more guess work or eyeballing. Graduated in all the following. OZ, Drams, CC, ML, TSP, TBS.   10 cups for $1.00,  50 cups for $3.00.

Quantity


Mixing Beakers  Larger size 100 ML (3 1/4 oz) mixing breaker with pour spout. Nice graduated raised letters that are very easy to read. Makes accurate mixing of any 2 part epoxy or resin so much easier, no more guess work or eyeballing. Perfect for expandable foam.    1 beaker for $1.00 or 10pcs for $7.50
Quantity


Mixing Sticks  Used for mixing epoxy or paint. 50 sticks per pack. 4 1/2 inches long.  $1.70 per pack.



Top Flight Micro Balloons  Micro balloon filler is ideal for thinning epoxy to make joints,  fillets, or repairing surface imperfections. Makes epoxy lighter and more sandable. A 3-1 ratio makes an easy to sand filler.


Milled Fiberglass Epoxy Strengthener  This is milled fiberglass that is used to strengthen any epoxy and speed up setting time. Mix 1/4 to 1/2 teaspoon per ounce. Perfect for installing your internal fin bracket. 4OZ bottle
 


1/8 Line Barb  These line barbs can easily be added to 1/8 k&s brass tubing by either soldering or using loctite.
 4 solid brass barbs per pack for $1.60



5/32 Line Barbs   These line barbs can easily be added to 5/32 OD tubing by either soldering or using loctite.
 4 solid brass barbs per pack for $1.90



K&S Brass Tubing  Tubing is sized by outside diameter and is .014 wall thickness. Sold in 1 foot lengths.

Sizes


Teflon Lined Brazed Stuffing Tubes  For 3/16 and 1/4 flex cables. Comes with teflon liner.
3/16 size is made from 9/32 tube with 1/4 reduced end and 12-24 inches long
1/4 size is made from 11/32 tube with 5/16 reduced end and 12-24 inches long
Sizes


Teflon Liner for .150 Flex Fits the K&S 1/4 brass tube. Sold by the foot for $2.50



 .150 Flex Brass Stuffing Tube w/ Teflon Liner  Perfect stuffing tube for .150 flex.
Sold in 1 foot lengths for $5.00



6mm Brass Stuffing Tube w/ Liner  For use with 4mm or .150 flex cables. Replacement stuffing tube with liner for Prince-Rocket. Also great for .150 flex cable.  
300mm long (12"). 
$5.00


7mm Brass Stuffing Tube w/ Liner  For use with 3/16 flex cables. Replacement stuffing tube with liner for Pursuit.  
300mm long (12"). 
$6.00


Auto Bailer    Allows water to exit hull when boat is in motion and automatically stops when boat is at rest. This is a 2pc design which makes cleaning easy. Just unscrew to clean.  $6.00


Radio Box  Laser cut radio box with plexiglass top and rubber sear, two servo mount included.
4 1/4" (108mm) wide x 6 1/4" (160mm) long  $10.00



3M Velcro
.  This is industrial strength 3M Velcro brand velcro with the strongest adhesive back made (blue label). Very strong. This is a great way to keep the lipos or batts in place. Once you know where you want your batts just stick the hook side to your hull and the loop side to your lipos and your good to go. They will not move. Comes in 1 or 2 inch wide. Sold by the foot. You can cut the 2" in half and have enough for 2 pairs of lipos.
 

Sizes x 1 foot


Velcro One-Wrap straps  1 inch wide. A great way to hold down your Lipos or batts.    $1.00 per foot.



Small Air Inlet  CNC Machined aluminum air inlet with stainless hardware. Adds a little bling.
75x25x2mm thick. (2.95" x 1" x .08")   $4.00 each


Medium Air Inlet  CNC Machined aluminum air inlet with stainless hardware. Adds a little bling.
100x30x2mm thick. (3.9" x 1.2" x .08")   $4.00 each


Large Air Inlet  CNC Machined aluminum air inlet with stainless hardware. Adds a little bling.
120x74x2mm thick. (4.7" x 2.9" x .08")   $6.00 each


Snap Off Razor Knives      Large is 3/4"wide with 8 blades. Small is 3/8"wide with 10 blades.                                                     Large only .25 cents each.     Small is only .15 cents each.

Sizes


Liquid Paint Mask  Bob Dively Liquid Masking Film can be sprayed, brushed or rolled on. Liquid Masking Film is a  strippable coating to mask and protect the finish when applying trim colors, letters, insignias. Tight radius curves can be easily made even on curved surfaces. Leaves sharp, clean paint lines. LMF air dries in 1 to 2 hours. Score with a new X-acto knife and peel off areas to be painted.
Can Size


Pactra Paint Masking Tape  Designed for use on R/C cars, model planes, rockets, boats and plastic model kits. A flexible, sharp-line paint mask. Thin film prevents edge build up. Stretch characteristics allow small radius curves. Low tack for easy removal. Comes in 20' lengths. Widths of 1/8, 1/4 and 1/2 inch.  $5.60 ea.
Widths


Hobbico CA Applicator Tips   Package of 6 CA Applicator Tips provides pinpoint accuracy.  Ideal for hard to reach area. Tips attach to the CA bottle tip.  .95 cents for pack of 6


Syringe 12cc  Curved tip syringe. Perfect for applying grease or glue in tight places. Two piece plastic construction with rubber seal on the plunger. Curved tip can be cut to increase the opening size.   $1.80


4" Colored Zip Ties   Red, White, Blue, Yellow, Black, Orange. Sold in packs of 25pcs for .75 or 100pcs for $2.50

Quantity
Colors
Website Builder